Skip to content
GableGreens

Deck Board Calculator

Count the deck boards, joists and screws for a rectangular deck, with board gaps and waste included.

Illustration of deck boards being screwed onto a frame

Deck and boards

A “5/4 × 6” or “2 × 6” board measures 5.5 in.Common widths are 120 mm and 144 mm.

How the deck board calculation works

  1. Rows. Deck width ÷ (board width + gap), rounded up.
  2. Total length. Rows × deck length.
  3. Boards. Total length × (1 + waste) ÷ the length of one board, rounded up.
  4. Joists. Deck length ÷ joist spacing, rounded down, plus one for the end.
  5. Screws. Rows × joists × 2.

boards = roundup( roundup( width ÷ (board + gap) ) × length × (1 + waste) ÷ board length )

Example: a deck 12 ft long and 10 ft wide with 5.5 in boards and a 1/8 in gap needs 120 ÷ 5.625 = 21.3, so 22 rows. That is 264 ft of board. With 10% extra, 290 ft ÷ 12 ft = 24.2, so buy 25 boards. Joists at 16 in: 144 ÷ 16 + 1 = 10. Screws: 22 × 10 × 2 = 440.

Example: a deck 3.6 m long and 3 m wide with 120 mm boards and a 5 mm gap needs 3,000 ÷ 125 = 24 rows. That is 86.4 m of board. With 10% extra, 95 m ÷ 3.6 m = 26.4, so buy 27 boards. Joists at 400 mm: 3,600 ÷ 400 + 1 = 10. Screws: 24 × 10 × 2 = 480.

Actual board sizes

Sold asActual widthActual thickness
5/4 × 6 decking5.5 in1 in
2 × 65.5 in1.5 in
2 × 43.5 in1.5 in
Common decking boardWidthThickness
Softwood, standard120 mm28 mm
Softwood, wide144 mm28 mm
Composite, typical138–150 mm20–25 mm

Sizes vary by supplier. Measure a board or read the product sheet, and enter the real width.

Joist spacing guide

Decking and layoutTypical spacing (in)Typical spacing (mm)
Timber boards, laid straight16400
Timber boards, laid diagonally12300
Composite boards12–16300–400

These are common figures. The board maker's installation guide and local code take priority.

Before you buy

  • Buy boards as long as the deck where you can, so each row is one piece with no joints.
  • If the rows end in a narrow strip, adjust the gap slightly or plan to rip the last board.
  • Use exterior-grade or stainless screws rated for the timber treatment or the composite you chose.
  • Add boards for fascia, steps and picture-frame borders. They are not included here.

Common questions

How many deck boards do I need?

Divide the deck width by the board width plus the gap to get the number of rows. Multiply the rows by the deck length to get the total board length, add about 10 percent for cuts, then divide by the length of the boards you will buy.

What gap should I leave between deck boards?

A gap of about 1/8 inch (3 mm) is common for dry timber and many composite boards. UK guidance for timber decking is often 5 to 8 mm. Wet pressure-treated boards are often laid tight because they shrink as they dry. Always follow the board maker's instructions.

How far apart should deck joists be?

16 inches (400 mm) on centre is the usual spacing for timber decking laid straight. Composite boards and diagonal layouts often need 12 inches (300 mm). The board maker and your local building code set the limit.

How many screws do I need for a deck?

Plan two screws where each board crosses each joist. The calculator multiplies rows by joists by two. Buy a little extra, since boxes are sold by count or weight.

Does this calculator design the deck frame?

No. It counts the surface boards, the joists at your chosen spacing and the screws. Joist size, spans, beams, posts and footings are structural and must follow your local building code.

Monthly home energy tips

One email a month with our new guides, a free calculator to try and the latest electricity prices. Unsubscribe any time.

The signup form is provided by Hostinger Reach and loads when you click. You confirm by email before you get anything. Privacy policy.

Embed this calculator on your website

Free to use on any website. Copy the code below and paste it into an HTML or custom code block. Please keep the credit line under it.

Preview

Published